## How do you calculate plywood for a roof?

## How do I calculate sq footage?

To find square feet, **multiply the length measurement in feet by the width measurement in feet**. This yields a product called the area, which is expressed in square feet (or square inches if you are calculating a much smaller space, such as a dollhouse).

## How do you calculate plywood for a roof?

**Divide the total roof area by 32** to get the number of sheets you will need to cover the roof. A typical 4 foot by 8 foot sheet of plywood covers 32 square feet. If your roof area is 1,600 square feet, 1,600 divided by 32 will mean you need about 50 sheets to cover the roof.

## Can you use 3/8 plywood roof sheathing?

Sheathing Thickness

You may see 3/8-inch plywood installed as roof sheathing and, although it may feel inadequate compared to 1/2-inch plywood installed on rafters spaced 24 inches on center, 3/8-inch plywood was, at one time, **considered acceptable in some jurisdictions**.

## How much does a 4x8 sheet of roofing plywood cost?

Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend **between $70 to $100 for each sheet of plywood**. A 4 x 8 sheet of plywood covers about 32 square feet of roof area—and the average roof measures about 3,000 square feet.Oct 6, 2021

### Related questions

##### Related

### How thick should roofing plywood be?

Most roofs will be sheathed in plywood at least 3/8 inch thick. That will suffice on a **roof with** rafters set 16 inches apart with minimal roof loads. Loads will vary with the pitch of the roof; the flatter the roof, the greater the load on any one section. Steeper roofs will have lighter loads per square foot.Dec 6, 2018

##### Related

### What is a 12 6 roof pitch?

The angle, or pitch, of a roof is calculated by the number of inches it rises vertically for every 12 inches it extends horizontally. For example, a roof that rises **6 inches for every 12 inches of horizontal run** has a 6-in-12 pitch.

##### Related

### Is the square footage of a house the same as the roof?

Roofing Quote **Footage is Not the Same as Home Square Footage**

Depending on where the information is coming from is going to determine the basis on which the estimated roof footage is calculated. The roof square footage is what we (roofing contractor) need to calculate a budget quote to do the job.Apr 15, 2014

##### Related

### Is 7/16 OSB OK for roofing?

Standard types of wood designed for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, without edge support, can be used in an area where the **snow load is 30 pounds per** square foot.

##### Related

### What grade of plywood is used for roof sheathing?

**1/2 or 3/4-inch Plywood** for Roof Sheathing? – Traditionally, 1/2-in CDX plywood was common choice with 24-in rafter spacing. However, heavier roof loads may require the use of 3/4-in CDX plywood for roof sheathing. Roofs with less pitch often carry heavier loads, including snow and ice accumulations in the winter.May 2, 2016

##### Related

### What should I use for roof sheathing?

**Oriented Strand Board (OSB) or plywood can be** used, although plywood will provide higher nail head pull-through resistance. Use panels rated as “Exposure 1” or better. Install sheathing panels according to the recommendations of the Engineered Wood Association (APA). Use panels no smaller than 4 feet long.

##### Related

### What type of plywood is used for roofs?

**CDX** is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes).Apr 11, 2020

##### Related

### How do you calculate plywood?

**Divide by the total square footage by the square footage of a sheet of plywood** to find the number of sheets required to cover the space. A 4×8 sheet of plywood is 32 ft^{2}. For example, if the area to be covered in plywood is 800 ft^{2} then 25 sheets of plywood will be needed to cover it.

##### Related

### Can you put plywood over plywood on roof?

The risk is that many of the nails could miss the rafters, and will simply **fasten the new plywood to the old plywood**. The result could be a poorly attached roof surface, more vulnerable to wind damage.Aug 26, 2001

##### Related

### What type of wood is best for roofing?

Longevity. In terms of cost-savings, **cedar wood** is long-lasting, making it an ideal roofing material. Cedar lasts at least 10 years longer than common roofing materials, like asphalt shingles.Nov 10, 2016

##### Related

### When should you replace plywood on a roof?

As plywood lasts **about 30 to 40 years** and we run the risk of delamination and required replacement in a few years. The other two have stated that as long as the plywood is good and stays dry, it can last forever.

##### Related

### How thick of plywood to put on a roof?

- The wider the rafter spacing, the heavier the shingling, the lower the slope and the heavier the weather load, the thicker the
**plywood**will have to be. Most roofs will be sheathed in**plywood**at least 3/8 inch thick. That will suffice on a**roof**with rafters set 16 inches apart with minimal**roof**loads.

##### Related

### How do you estimate the price of a roof?

- You can estimate roofing costs once you have all this information. Typically, you can determine the cost of materials by
**multiplying the roof's square footage by the cost per square foot of material**. Identify the areas you need to roof.

##### Related

### How much does roofing plywood cost?

- Depending on the thickness, plywood can cost anywhere from
**$5 to as much as $55**for a 4×8 sheet. For example, a 4×8 that 1/4″ thick can cost $6, while a 4×8 that is 11/32″ thick can cost around $15. See our chart below to give you a better idea of what you may pay at a local hardware store.

##### Related

### How do you calculate shingles on roof?

- To estimate how many shingles you'll need, first
**estimate the total square footage of your roof's surface**. To do this, measure the length and width of each plane on the roof, including dormers. Then,**multiply length x width**to get the square footage of each plane.

##### Related

### How to calculate the number of sheets of plywood needed for a roof?How to calculate the number of sheets of plywood needed for a roof?

Once you have the area you can divide by the area of a sheet of plywood to find the number of sheets needed. A 4×8 sheet of plywood is 32 ft 2. So, dividing the area of the roof by 32 will give you the number of sheets needed.

##### Related

### How big is a sheet of plywood for a gable roof?How big is a sheet of plywood for a gable roof?

The calculation is based on that the Plywood or OSB (Oriented Strand Board) sheets are of a 4' x 8' size. One sheet = 32 ft² This basically calculates the number of sheets needed for a Gable roof. The square footage of a Hip roof area is identical to the square footage of a Gable roof of the same measurements.

##### Related

### How big is a 4x8 sheet of plywood?How big is a 4x8 sheet of plywood?

A 4×8 sheet of plywood is 32 ft 2. For example, if the area to be covered in plywood is 800 ft 2 then 25 sheets of plywood will be needed to cover it.

##### Related

### How to get a free roofing estimate for Your House?How to get a free roofing estimate for Your House?

Just plug in your house dimensions, select your roof pitch, relative roof difficulty, choice of materials, and let our Calculator do the rest. To get a 100% free roof quote, enter your zip code above and fill out a simple estimate request form on the next page.